Dépannage étape par étape pour chaque robot piscine Aiper — séries Scuba, Seagull Pro et Surfer. Choisissez votre modèle et obtenez des réponses rapides : installation, Wi‑Fi, nettoyage, erreurs et pièces.
Scuba V3 Troubleshooting
10 guidesCordless robotic pool cleaner with wall-climbing and night-light features. Covers all Scuba V3 firmware versions.
How to Factory Reset the Aiper Scuba V3
To factory reset the Scuba V3, hold the power button for 10 seconds until the LED flashes three times.
Full guide →Aiper Scuba V3 App Setup — First-Time Pairing Guide
Download the Aiper app (iOS / Android), tap ‘+’ → Scuba V3.
Full guide →Scuba V3 App Disconnects When Robot Is in the Pool
This is expected behavior, not a defect.
Full guide →Scuba V3 Won’t Stop Cleaning — Loop Fault Fix
A loop-cleaning fault is caused by a stuck tangle sensor beneath the brush roll or a corrupted schedule entry.
Full guide →Scuba V3 Not Climbing Walls — What to Do
The Scuba V3 is a floor-only cleaner — wall climbing is not a supported feature and this is not a defect.
Full guide →Scuba V3 Night Light Not Activating — Diagnosis & Fix
The V3’s LED night indicator requires the ambient light sensor to read below 50 lux.
Full guide →Aiper Scuba V3 Battery Life & Replacement Guide
A fully charged Scuba V3 takes 5 hours to charge and delivers 180 minutes (3 hours) of cleaning time.
Full guide →How to Clean the Aiper Scuba V3 Filter Basket
Rinse the filter basket under running tap water after every 2–3 sessions.
Full guide →Is the Aiper Scuba V3 Safe for Saltwater Pools?
Yes — the Scuba V3 is rated for saltwater pools up to 3% NaCl concentration (standard residential chlorinator output).
Full guide →Aiper Scuba V3 vs Scuba X1 — Which Should You Buy?
The V3 offers 90-minute floor-only cleaning.
Full guide →Scuba S1 Troubleshooting
10 guidesAffordable cordless floor cleaner with app control. Covers 2024, 2025, and 2026 hardware revisions.
How to Register the Aiper Scuba S1 in the App
Open Aiper app → tap ‘+’ → select Scuba S1.
Full guide →Scuba S1 Wi-Fi Setup — Incorrect Password & 2.4 GHz Fix
The most common cause of a Wi-Fi error on the Scuba S1 is a 5 GHz network — the S1 only supports 2.4 GHz.
Full guide →Aiper Scuba S1 Not Cleaning Properly — Diagnosis & Fix
First check that the filter basket is clear and the robot is fully charged.
Full guide →Scuba S1 Offline or Dropped from App — Reconnection Guide
The Scuba S1 disconnects from Wi-Fi when it enters the water — this is expected behavior.
Full guide →Scuba S1 Gets Stuck in the Pool — Causes & Prevention
A stuck S1 is usually caused by debris lodged in the rear drive wheel or a tangle in the brush roll.
Full guide →Aiper Scuba S1 Filter Replacement — How to Order & Schedule
Replacement filter baskets for the Scuba S1 are not listed on the Aiper website as a direct-purchase item.
Full guide →Aiper Scuba S1 Battery Care & Long-Term Storage
Charge fully (4 hours) before first use.
Full guide →Aiper Scuba S1: 2024 vs 2025 vs 2026 — What Changed?
The Scuba S1 2026 upgrade is now available across all official Aiper regional stores.
Full guide →Aiper 3-Micron Micromesh Filter — Performance & Replacement
The S1’s 3-micron filter captures sand, algae spores, and pet dander — 10× finer than a standard 30-micron basket.
Full guide →Aiper Scuba S1 vs Scuba V3 — Full Comparison
The S1 adds wall-climbing, 3-micron filtration, Wi-Fi scheduling, and quad motors vs the V3’s dual-motor floor-only design.
Full guide →Scuba X1 Troubleshooting
11 guidesPremium wall-climbing robot with HydroComm smart navigation. Covers X1, X1 Pro, and X1 Pro Max.
Scuba X1 Initial Setup & First Run
Turn on the Scuba X1 and allow the 30-second initialization process to complete before placing it in the pool.
Full guide →Scuba X1 vs X1 Pro vs X1 Pro Max — What’s Different
The three X1 models share the same core platform.
Full guide →Scuba X1 Wi-Fi Setup & App Connection Guide
The Scuba X1 requires a 2.4 GHz Wi-Fi network.
Full guide →Scuba X1 Pro & Pro Max: HydroComm Setup & Troubleshooting
HydroComm lets you monitor and control the X1 Pro / Pro Max while it is submerged.
Full guide →Scuba X1 Eco Schedule Not Working — Firmware Error Fix
The most common cause is a false firmware update notification — the app shows « firmware update needed » but the robot is already on the latest version.
Full guide →Scuba X1 Not Cleaning Properly — Diagnosis & Fix
First check that the filter basket is clear and the robot is fully charged.
Full guide →Scuba X1 Pro & Pro Max: Wall Climbing Issues
Wall climbing requires a full charge and the correct mode.
Full guide →Scuba X1 Filter & HydroComm Probe Replacement
Replacement filter baskets and HydroComm probes for the Scuba X1 are not available on the Aiper website.
Full guide →Scuba X1 Battery Not Charging or Beeping During Charge
Beeping at 75–80% charge indicates a charging port or battery management issue.
Full guide →Scuba X1 Error Codes & Factory Reset Guide
Most X1 errors clear with a power cycle or factory reset.
Full guide →Seagull Pro Troubleshooting
7 guidesSolar-rechargeable surface skimmer. Includes critical ZT6001 battery recall safety notice.
Seagull Pro Battery Recall — ZT6001 Safety Notice
STOP USE IMMEDIATELY if your Seagull Pro serial number begins with « 61 ».
Full guide →Seagull Pro Initial Setup & First Run
Charge the Seagull Pro fully before the first use.
Full guide →Seagull Pro Not Cleaning Walls Properly
The most common causes are: filter basket clogged (reduces suction/traction) or wrong cleaning mode selected.
Full guide →Seagull Pro Stuck or Won’t Move
If the Seagull Pro stops moving, check the filter basket and drive rollers first.
Full guide →Seagull Pro Filter Basket Replacement — How to Order
Replacement filter baskets for the Seagull Pro are not available on aiper.com.
Full guide →Seagull Pro Battery & Charger Replacement
Aiper does not replace the Seagull Pro battery as a standalone part — if the battery is defective under warranty, the entire unit is replaced.
Full guide →Seagull Pro Error Codes — LED & App Errors
Most Seagull Pro errors are indicated by LED blink patterns and corresponding codes in the Aiper app.
Full guide →Surfer S2 Troubleshooting
8 guidesWi-Fi-enabled surface skimmer with eco scheduling. Also covers the EcoSurfer S2 variant.
Surfer S2 Initial Setup & First Float
Charge fully, then power on and complete Wi-Fi pairing within 5 minutes of turning the device on.
Full guide →Surfer S2 Eco Schedule & Timer Setup
The Surfer S2 supports scheduled automatic cleaning via the Aiper app.
Full guide →Surfer S2 Not Skimming Properly — Fix Guide
First check whether the filter basket is full and whether the robot is fully charged.
Full guide →Surfer S2 Motor Not Working — Propeller Jammed Fix
A non-working motor is most commonly caused by saltwater crystallization locking the propeller shaft, or debris wrapped around the propeller.
Full guide →Surfer S2 Charging Cable & Battery Replacement
Replacement charging cables for the Surfer S2 (model GQ12-126100-HU) are not available on the Aiper website.
Full guide →Surfer S2 Filter Basket Replacement
Replacement filter baskets for the Surfer S2 are not available on the Aiper website.
Full guide →Scuba N1 Troubleshooting
8 guidesAdvanced cordless cleaner covering floor, walls, and waterline. Includes N1 vs N1 Pro comparison.
Scuba N1 Initial Setup & First Run
Charge fully and add the robot to the Aiper app before placing it in the pool.
Full guide →Scuba N1 vs N1 Pro — What’s Different
The N1 Pro adds upgraded suction power and a larger filter basket capacity compared to the base N1.
Full guide →Scuba N1 Schedule Feature — Eco Mode Replaced
In the 2025 firmware update, Eco Mode was removed and replaced by a Schedule feature.
Full guide →Scuba N1 Not Picking Up Debris — Diagnosis & Fix
Check the filter basket first — a clogged basket is the most common cause.
Full guide →Scuba N1 Stuck or Won’t Move
Lift the N1 out of the pool, clear any debris from the drive rollers, and restart.
Full guide →Scuba N1 Filter Basket & Parts Replacement
Replacement filter baskets for the Scuba N1 are not available on the Aiper website.
Full guide →Scuba N1 Battery Issues, Error Codes & Factory Reset
Red flashing LED during charging with a high battery temperature warning means stop charging immediately and contact support.
Full guide →Scuba SE Troubleshooting
7 guidesEntry-level cordless pool cleaner with wall-cleaning capability. Includes SE vs N1 vs S1 comparison.
Scuba SE Initial Setup & Charging Indicator Guide
The charging LED works in three stages: green (charger alone) → red (charging) → green (fully charged).
Full guide →Scuba SE vs N1 vs S1 — Which Model Do You Have?
The Scuba series includes multiple models at different capability levels.
Full guide →Scuba SE Path Preference & Schedule Feature
Path preference adjusts the SE’s cleaning pattern via the app.
Full guide →Scuba SE Not Cleaning Properly — Diagnosis & Fix
Check the filter basket first — a clogged basket reduces suction.
Full guide →Scuba SE Stuck or Won’t Return from Wall
The SE requires a 90-degree wall angle to detect the wall and reverse.
Full guide →Scuba SE Parts Replacement — Filter, Axle & Mesh
All Scuba SE replacement parts — filter basket, axle, mesh screen — are not available on the Aiper website.
Full guide →Surfer S1 Troubleshooting
7 guidesSolar-powered surface skimmer with Wi-Fi app control and solar top-up charging.
Surfer S1 Initial Setup & First Float
The Surfer S1 is a solar-assisted surface skimmer — it charges both via the included wall charger and via its built-in solar panel.
Full guide →Surfer S1 Solar Charging — How It Works & Troubleshooting
The Surfer S1 solar panel supplements the battery during daytime operation.
Full guide →Surfer S1 Wi-Fi Setup & App Connection
The Surfer S1 requires 2.4 GHz Wi-Fi and a Bluetooth-enabled phone for initial pairing.
Full guide →Surfer S1 Schedule & Firmware Update Guide
Schedule not working is the most reported issue for the Surfer S1.
Full guide →Surfer S1 Not Skimming Properly
Check whether the filter basket is full and whether the solar panel is clean (dirty panel reduces power).
Full guide →Surfer S1 Motor Not Working & Propeller Issues
If the motor does not spin, check for debris wrapped around the propeller and saltwater crystallization on the shaft.
Full guide →Surfer S1 Parts & Charging Cable Replacement
Surfer S1 replacement parts (filter basket, charging cable, propeller blades) are not available on the Aiper website.
Full guide →